ONE COMPONENT, LOW VOC FLOOR COLOR COATING SYSTEM.

MIXING

• Material should be preconditioned to a minimum of 50˚F (10˚C) prior to use. The material temperature must be brought to 5°F above the dew point temperature. Relative humidity should be below 75%.
• Do not apply if rain or heavy dew is expected within 24 hours.
• Mix it well before use

APPLICATION

• Apply with high quality pump sprayer at a fine spray setting using a circular motion.
• Allow first coat to dry before deciding if a second coat is necessary. An additional coat will provide a darker and more uniform color.
• Note: horizontal surfaces may be subject to premature wear. Periodic touch ups may necessary.
• For added protection, use a product such as ULTRASEAL.

DRY TIME 

• Longer dry time required in cooler temperatures and in higher humidity. Allow 24 hoursfor light foot traffic.
• Surfaces may be subjected to light foot traffic after 24 hours. Allow 72 hours before subjecting surface to heavy traffic, repositioning furniture or automotive traffic. Park tires on corrugated card board for 7 days after applying stain. After 30 days, clean as needed with a mild, non-abrasive liquid detergent.

CLEAN-UP

•  Clean with soap and water.
• Properly dispose of all soiled rags and protect unused product from freezing.
• For disposal of empty containers and unused paint, contact your household refuse collection service.

• Provide for expansion and control joints as specified per TCNA Method EJ171 or per TTMAC Specification Guide 09 30 00, Detail 301MJ. Do not cover expansion joints with cement mortar.
• Protect POLICRETE work with metal strips (edge metal) along both edges of structural building expansion joints.
• Protect the installation from foot traffic, rain and freezing for 24 hours.

All the major components or compounds used to make EZ DYE are ISO9000 certified. What are the standards established by the International Organization for Standardization (ISO) to guarantee quality in the production of goods or services.

WARNING: Keep away from sparks, heat, and open flame. Use with adequate ventilation. Prolonged or repeated breathing vapor or spray mist can cause headache, nausea, dizziness or confusion. This product can be harmful if inhaled, swallowed, or absorbed through the skin.

HAZARDS: Avoid breathing vapor, spray mist or contact with the skin. Use only with adequate ventilation during mixing, application and drying. Use face protection, gloves and full protective clothing to prevent contact. Wear appropriate self-contained respiratory equipment when handling. Use only with recommended thinners and cleaners. Keep away from heat, sparks, arc, and open flame.

FIRST AID: In case of contact with skin, flush with water and get immediately medical attention. For eyes, immediately flush with plenty of water for at least 15 minutes and get immediately medical attention. In case of exposure of high concentrations of fumes, remove to fresh air and get immediately medical attention. If swallowed, get immediately medical attention. Do not induce vomiting. See product material safety data sheet for further details on contents and procedures to follow.

PRECAUTIONS: Improper use and handling of this product can be hazardous to health or cause a fire. Consult all Federal Regulations concerning occupational safety and health standards and any other applicable Federal, State, and Local regulations on safety practices in coatings operations. Necessary safety equipment must be used, and proper ventilation requirements carefully observed, especially in confined or enclosed spaces to prevent build-up of vapors.

SPILLAGE: Extinguish all sources of ignition. Use absorbent cleanup materials. Prevent from entering sewers or waterways.

FIRE: Blanket flames with dry chemical, carbon dioxide, or foam. Wear self-contained breathing apparatus.

STORAGE & DISPOSABLE: Store in cool, well, ventilated area. Keep containers closed and upright when not in use to prevent leakage. Dispose of in separate closed metal container in accordance with all applicable regulations.

CLEAN UP: Clean up the equipment with xylene, alcohol or other environmentally safe solvent. Dispose of waste solvent according to local environmental regulations. CAUTION: These solvents may be flammable. Keep away from all sources of ignition. Clean skin with soap and warm water. Do not use abrasive cleaners which may cause irritation.

EXCLUSION OF WARRANTIES: Trends Design USA, Inc (POLICRETE) makes no warranties, expressed or implied, in connection with the sale of (this)(these) product(s) and all implied warranties of merchantability and fitness for a particular purpose are excluded and shall not apply to the goods sold. Trends Design USA, Inc (POLICRETE) employees, agents, and/or representatives may have made oral statements about the merchandise sold. Such statements do not constitute warranties and are not a part of the contract for sale of the products sold.

LIMITATION OF REMEDIES: Whether for breach of contract or warranty, negligence of Trends Design USA, Inc (POLICRETE), strict liability or otherwise Trends Design USA, Inc shall not be liable for anu incidental, special, or consequential damages whatsoever. The sole remedy available from Trends Design USA, Inc. is the refund of the contract price for the goods for which liability is claimed.

SEVERABILITY: If the above exclusion of warranties provision, or any part thereof, should be held invalid or unenforceable, the limitation of remedies provision shall apply in full force and effect. If anu provision of the limitation of remedies clause should be held or unenforceable, all other provisions in that clause shall nevertheless continue in full force and effect.